Home
// Digital Technology - Year 9 & 10 //

CHAIN REACTION
MACHINES

Over the next 10 links you and a partner will design and 3D print one section of a giant class machine: every stage starts the next, every part is printed, and every section passes the ball to the one after it. Then the whole class runs it on Relay Day.

⛓️ Chain Reaction
📐 Tinkercad CAD
👥 Pair Sections
🏁 Relay Day
Machine Kit
📐
Design Platform
Tinkercad - free browser-based CAD. Join your class below, then log in with your class login (not a personal Autodesk account).
🖨️
The Print Shop
5x FlashForge Adventurer 3 printers. Each part must fit inside 150 x 150 x 150mm, the nozzle is 0.4mm, and a printed part can be out by about 0.2mm either way. Submit your parts through Connect and they join the shared print queue.
⚠ Everything is printed, even the ball. Nothing else goes in your machine.
🚪
Standard Gate
Every section starts with the same input funnel and ends with the same output chute, and every pair uses the same 20mm printed ball. The exact numbers are in Link 02. Get them right and any two sections link up.
🧩
Fit Toolkit
Pivots and flaps need a 0.3-0.5mm moving gap so they swing. Track joints use a 0.1-0.2mm snug gap so they line up. Printed holes come out small, and your Link 03 coupon proves what rolls.
🧠
AI Assistant
copilot.microsoft.com - ask it "How do I do X in Tinkercad?" or "Why does my ball stop here?" whenever you're stuck.
⚠ AI can get tool names and measurements wrong - check against the real editor and your coupon!
🏁
Relay Day
Every section in one line, desk to desk. The class gets 3 attempts at one unbroken run, filmed, with 5 minutes to fix between attempts. Then vote: Most Reliable, Best Mechanism, Best Hand-off and People's Choice.
// Primary Objective

With a partner, design and 3D print one section of a class chain reaction machine that catches the ball from the section before, runs 3 to 4 stages, and passes the ball to the section after, every single time.

Design 3 to 4 printed stages between the class funnel and chute, on one desk
Test your track, pivots and dominoes with coupons and 10-run success rates
Fix the weakest link with evidence, until every stage works 10 out of 10
Link your section into the class relay and run it on Relay Day
// Marking Key & Rubric
Criteria Sketch
(0-1)
Rough Run
(2-3)
Reliable
(4)
Relay Ready
(5)
Score
Design & Modelling Few parts modelled, or the funnel and chute do not match the Standard Gate Most parts modelled, funnel and chute close to the spec, most design rules followed Every part clean and printable, funnel and chute exactly to the spec, 3 or more stages Stages flow neatly on one desk, parts are tidy and reusable, and every gap is deliberate / 5
Mechanisms Stages do not move or do not pass to the next Most stages work but some hand-offs fail Every stage and hand-off works, including a pivot (seesaw or flap) Mechanisms are clever and reliable, and the section runs 10 to 20 seconds / 5
Testing & Fixing No coupon or test log Coupon and some success rates recorded, with at least one fix Success rates for every stage, and fixes written as evidence, change and reason Fixes proven by new success rates, and the section reaches 10 out of 10 / 5
Relay & Teamwork Section not ready for the relay, or partner work very uneven Section docked for the relay with some help Docks with both neighbours, clear reset card and fix plan, fair partner work Hand-offs work every time, fixes made calmly between attempts, and feedback acted on / 5
Total / 20
Scroll sideways to see every column
Build Log
Week 1
01
⛓️ Chain Reactions
▾
// LINK OBJECTIVEPartner chosen, the energy chain explained for 3 stages of a real machine, and a sketch of your own 3 to 4 stage section with the standard funnel and chute marked.
  • Learn the challenge: working in pairs, you will design and 3D print one section of a giant class chain reaction machine. Every part is printed, even the ball
  • Every section starts with the same input funnel and ends with the same output chute, so on Relay Day every section links to the next one, desk to desk
  • Watch a real machine and track the energy: each stage starts with energy stored (a raised ball, a balanced arm, a standing domino) and turns it into movement that starts the next stage
  • Pick 3 stages from the video and write the energy chain for each: what was stored, what moved, what it started
  • Read the six stage types below. Choose 3 or 4 for your section, in order
  • Sketch your section from above and from the side, on one desk. Mark the funnel on the left, the chute on the right and every stage between them
🛝 RampStored height turns into rolling. Slope and channel width come from your Link 03 coupon.
⚖️ SeesawA ball lands on the high end, the arm tips and the other end pushes or drops something.
🎯 Domino RunPrinted dominoes in a line. Each one falls and knocks the next.
🚪 Release FlapA swinging flap holds a stored ball until something hits it.
🌀 Funnel DropA ball spirals or drops through a funnel to change direction or height.
🔀 Switch TrackA ball rolls one way, tips a printed switch, and sends the next ball another way.
💡 HintReliable beats complicated. On Relay Day a simple section that works 10 times out of 10 is worth more than a clever one that works half the time.
// ASK AI"Explain how energy is stored and released in each stage of a Rube Goldberg machine"
02
🚪 The Standard Gate
▾
// LINK OBJECTIVEThe class input funnel, output chute and a test track modelled exactly to the Standard Gate spec, checked from every side and submitted.
  • Join your Tinkercad class using the login cards in your Machine Kit above, then log in with your last name
  • Read the Standard Gate spec below. These numbers are the same for every pair in the class, so do not change them
  • Model the input funnel: a hollow box or cone with a 50 x 50 mm opening, its rim 50 mm above the desk, and an exit hole that feeds your first stage. Give it a wide flat base so it does not tip
  • Model the output chute: a sloping channel that drops the ball 60 mm above the desk, 20 mm past your desk edge, rolling straight right
  • Model one short test track piece (about 120 mm long) with a channel for the 20 mm ball and walls at least half the ball's height
  • Use the size boxes to type every number exactly, then use the ViewCube to check each part from the front and the side
  • Submit your funnel, chute and test track
🚪 The Standard Gate (class spec)
BallThe class ball: a 20 mm printed sphere. Your teacher prints every ball from one file, so they all match
Input funnelOpening 50 x 50 mm, rim 50 mm above the desk, its centre 30 mm in from the left edge and 150 mm back from the front edge
Output chuteThe ball leaves the chute 60 mm above the desk, 20 mm past the right edge and 150 mm back from the front, rolling straight right
Run timeAbout 10 to 20 seconds from the ball landing in your funnel to your ball leaving your chute
💡 HintWrite the spec numbers on a sticky note on your screen. If one pair gets the chute height wrong, their neighbour's funnel misses the ball on Relay Day.
🔍 Google Image Search"marble run funnel and chute design"
// ASK AI"How do I model a hollow funnel with a hole in the bottom in Tinkercad?"
📤 Submit via ConnectYour input funnel, output chute and test track (Tinkercad share links)
// LEVEL UPAdd a small printed "dock" to your chute: a tab that slots into a matching notch on the next pair's funnel base, so the two always line up. Agree the tab size with your neighbours first.
Week 2
03
🧪 Track Test Lab
▾
// LINK OBJECTIVEA track coupon (channel widths 21 to 24 mm, four ramp slopes) tested with the class ball, and the width and slope that roll it every time recorded.
  • Learn the problem: a printed ball is a little lumpy and printed tracks are a little rough, and our printers can be out by about 0.2 mm. The only way to know what rolls is to test
  • Model a track coupon: four short channels side by side, each 60 mm long, with inside widths of 21, 22, 23 and 24 mm. Label each one with the Text shape
  • Model a slope block: a stepped wedge that tips the coupon to four different slopes, so you can test each channel at each slope
  • Write a prediction: which width and which slope will roll the class ball smoothly every time?
  • When the coupon is printed, roll the class ball down every channel at every slope, 5 times each. Record rolls, wobbles, sticks or jumps out
  • Choose your track width and minimum slope and write why, using your results
🧪 Track Rules
ChannelInside width a little bigger than the ball. Your coupon decides how much
WallsAt least half the ball's height (10 mm) so it can't jump out on a bend
SlopeSteep enough to keep rolling, gentle enough not to fly off the end. Your coupon decides
EndsEvery track end lines up flush with the next piece. A 1 mm step can stop a ball
💡 HintTest with the real class ball, not a glass marble. A heavier, smoother ball rolls on slopes the printed one stalls on.
🔍 Google Image Search"3d printed marble run track test"
// ASK AI"Why does a rolling ball slow down on a rough track compared with a smooth one?"
📤 Submit via ConnectYour track coupon and slope block (Tinkercad share links) and your prediction
// LEVEL UPAdd a 90 degree bend to your coupon and test whether the ball needs a steeper slope or taller walls to get round it. Record the slope that works.
04
⚖️ Levers & Seesaws
▾
// LINK OBJECTIVEA seesaw stage modelled on a pivot pin with a moving-fit gap, and a sketch showing what it starts and what starts it.
  • Collect your printed coupon and finish testing if you need to. Record your chosen width and slope
  • A seesaw stores nothing until a ball lands on it. Its weight tips the arm, and the other end moves something: it pushes a ball, drops a ball or tips a domino
  • Model the seesaw arm with a hole through the middle, and a stand with a pivot pin. The hole is bigger than the pin by a moving-fit gap (0.3 to 0.5 mm) so the arm swings freely
  • Put a small cup on the landing end so the ball stays on long enough to tip the arm
  • Add a stop so the arm can only tip one way and never falls off the pin
  • Sketch what starts your seesaw and what your seesaw starts. Mark the heights in mm
⚖️ Lever Rules
PivotHole = pin + 0.3 to 0.5 mm so the arm swings, not sticks
BalanceRest the arm with the landing end up: a small weight on the other end holds it there
CupA shallow cup on the landing end so the ball doesn't bounce off
StopA block on the stand so the arm can't swing past where you need it
💡 HintA longer arm on the landing side tips with less weight. If your ball isn't heavy enough, move the pivot towards the other end.
🔍 Google Image Search"3d printed seesaw lever marble run"
// ASK AI"Why does moving the pivot of a lever change how much force is needed to tip it?"
// LEVEL UPModel a second arm length and test both: which pivot position tips with the class ball every time? Record the distance from the pivot in mm.
Week 3
05
🎯 Triggers & Dominoes
▾
// LINK OBJECTIVEPrinted dominoes and a release flap modelled, with domino spacing and the flap's trigger planned and tested on paper.
  • Model a set of printed dominoes: thin, tall blocks with flat bases (try 8 x 20 x 40 mm). Print enough for your run plus spares
  • Plan your spacing: too close and a domino leans on the next one, too far and it misses. Test on paper first by drawing your dominoes to scale and checking each one reaches the next as it falls
  • A falling domino can knock over one about 1.5 times its own size, so a run can grow towards the end
  • Model a release flap: a small door on a pivot pin that holds a ball back. When something hits the flap, it swings open and the stored ball rolls
  • Give the flap the moving-fit gap on its pin, and check it falls open by itself once pushed
  • Decide the order of your stages and mark each hand-off on your sketch: what hits what, and where
🎯 Domino RunFlat bases, equal spacing, tested on paper first. A run can grow about 1.5x per domino.
🚪 Release FlapHolds a stored ball back. Moving-fit gap on its pin. One tap and it swings open.
⚖️ SeesawBall in, arm tips, other end moves something. Moving-fit gap on its pivot.
🛝 RampYour coupon's width and slope. Ends flush so the ball never trips.
💡 HintEvery hand-off is a place your machine can fail. For each one, ask: what if the ball arrives slower than I expect? Leave room for that.
🔍 Google Image Search"domino chain reaction growing size"
// ASK AI"Why can a falling domino knock over a slightly bigger domino?"
// LEVEL UPMake a domino run where every domino is a little bigger than the one before. Keep the growth under 1.5 times per domino and test whether the last one still falls.
06
🖨️ Print Queue
▾
// LINK OBJECTIVEEvery part laid flat, track pieces joined by pins and sockets, the Print-Ready Checklist passed, peer checked and submitted for printing.
  • Turn every part so it sits on its flattest face. Anything that sticks out past about 45 degrees needs support material, and supports left in a pivot hole can jam it
  • Join your track pieces with pins and sockets (snug fit, 0.1 to 0.2 mm) so they line up and the ends sit flush
  • Run the checklist below on every part. Fix anything that fails before you submit
  • Swap with another pair and check each other's parts with the checklist. Note one thing they got right and one to fix
  • Submit every part for printing: funnel, chute, tracks, seesaw, flap and dominoes
  • Start a test log (paper or Canva): stage, runs, successes, what went wrong, fix
✅ Print-Ready Checklist
SizeEvery part fits inside 150 x 150 x 150 mm and sits flat
WallsAt least 1.2 mm everywhere, and 2 mm around sockets and pivot holes
GapsPivots use the moving gap, track joints the snug one
GateFunnel and chute match the Standard Gate numbers exactly
BasesEvery standing part has a wide flat base so a passing ball can't knock it over
💡 HintSplit the printing between you: one partner checks the tracks, the other checks the moving parts. Then swap and check each other's.
// ASK AI"Why should a 3D printed part with a hole for a pin be printed with the hole facing up?"
📤 Submit via ConnectEvery part of your section (Tinkercad share links)
Week 4
07
🔁 Stage Testing
▾
// LINK OBJECTIVEEach stage run 10 times on its own, the success rate recorded for every stage, and the weakest stage named with evidence.
  • Collect your printed parts and inspect them: warping, droopy overhangs, rough track ends, stuck pivots. Note each problem in your test log
  • Set up each stage on its own and run it 10 times. Record how many runs worked: that is its success rate
  • For every failed run, write what went wrong: ball stalled, ball jumped out, arm did not tip, flap did not open, domino missed
  • Name your weakest stage: the one with the lowest success rate
  • Write one fix for it as evidence, change, reason
🔁 Success Rate
HowRuns that worked, out of 10. 7 out of 10 is 70%
Why 10One good run can be luck. Ten runs show how reliable a stage really is
Chain mathsStages that each work 9 times in 10 only all work together about 7 times in 10 for 3 stages
GoalEvery stage at 10 out of 10 before Relay Day
💡 HintReset every stage exactly the same way each time and mark where the ball starts with a pencil. Otherwise you are testing your reset, not your stage.
// ASK AI"If each stage of a machine works 90% of the time, how often does a 3-stage machine work all the way through?"
📤 Submit via ConnectYour test log with the success rate of every stage
// LEVEL UPWork out your whole section's chance of success by multiplying the stage success rates together (0.9 x 0.8 = 0.72). Which single stage, if fixed, would raise it the most?
08
🔧 Link & Tune
▾
// LINK OBJECTIVEAll stages linked into one section, the weakest link fixed and resubmitted, and the whole section run 10 times with its success rate logged.
  • Link all your stages into one section between your funnel and your chute, on one desk
  • Run the whole section 10 times, starting by dropping the class ball into your funnel from the chute height (60 mm). Record the success rate
  • Find the weakest link: the hand-off that fails most. Write it as evidence, change, reason
  • Duplicate your design before changing anything, fix one thing at a time, and note the measurement each time
  • Resubmit the fixed part for printing
  • Time your section from funnel to chute with a phone or the classroom clock: it should be 10 to 20 seconds
🔧 Fix Log Example
Evidence"Ball stopped on track 2, 6 runs out of 10"
Change"Make track 2 one slope step steeper"
Reason"On the coupon, the next slope rolled the ball 5 out of 5"
💡 HintMost failures happen at the hand-offs, not inside a stage. Watch the moment one stage passes to the next, again and again.
🔍 Google Image Search"marble run fix ramp angle"
// ASK AI"My printed ball keeps stopping halfway down a ramp. What are three different fixes, and how would I test which one works?"
📤 Submit via ConnectYour fix log, whole-section success rate, and the fixed part (Tinkercad share link)
// LEVEL UPAsk another pair to reset and run your section using only your written reset instructions. Every question they ask means your instructions need another line.
Week 5
09
🤝 Relay Rehearsal
▾
// LINK OBJECTIVEYour section docked with both neighbours, a full rehearsal run filmed, and a 5 minute fix plan written for Relay Day.
  • Push your desk against your neighbours' desks in the relay order your teacher sets
  • Dock your funnel under the chute of the pair before you, and your chute over the funnel of the pair after you. Check the Standard Gate numbers with a ruler
  • Run each hand-off between sections 5 times: drop the ball down your neighbour's chute and watch it land in your funnel
  • Join the class for a full rehearsal run, filmed, from the first funnel to the last chute
  • Write a 5 minute fix plan: the most likely thing to go wrong in your section on Relay Day, and exactly what you will do if it does
  • Write your reset card: the steps to put your section back to the start, in order
1. DockFunnel under the chute before you. Chute over the funnel after you.
2. Hand-offTest each hand-off 5 times before the full run.
3. Reset CardEvery step to put your section back to the start, in order.
4. Fix PlanYour most likely failure and what you do in 5 minutes.
💡 HintWatch the rehearsal film back in slow motion. The exact moment a ball stops tells you which hand-off to fix.
🔍 Google Image Search"class chain reaction machine relay"
// ASK AI"Help me write clear reset instructions for a chain reaction machine so someone else could set it up"
📤 Submit via ConnectYour reset card and 5 minute fix plan
10
🏁 Relay Day
▾
// LINK OBJECTIVEThe class relay run three times, your section reset and fixed between attempts, and your files, test log and reflection submitted.
  • Set up your section, run your own stages once to check them, then reset with your reset card
  • Relay rules: hands off once the countdown starts; only touch your own section; if your section fails, the class waits while you use your fix plan
  • Attempt 1: the whole class relay runs, filmed. Watch where it stops
  • You have 5 minutes to fix and reset between attempts. Then Attempt 2 and Attempt 3
  • The class votes: Most Reliable, Best Mechanism, Best Hand-off and People's Choice
  • Write your reflection: what worked, what failed and why, and what you would change with more time
  • Submit your final Tinkercad share links, your test log and your reflection
💡 HintBreathe before you reset. Most failures on the day come from a rushed reset, not a bad design. Follow your reset card line by line.
// ASK AI"Help me write a short reflection about designing a reliable section of a class chain reaction machine"
📤 Submit via ConnectYour final Tinkercad share links, your test log and your reflection
🏁

Relay Day Awaits

After 10 links of designing, testing and tuning, every section lines up desk to desk. The class gets three attempts at one unbroken run from the first funnel to the last chute, then votes for the awards.

⛓️ One class machine
🎬 Three filmed runs
🏆 Four titles to win

Find your partner and sketch your section // Link 01

SYSTEM ONLINE // YEAR 9 & 10 DIGITAL TECHNOLOGY CHAIN REACTION MACHINES // 10 LINKS